Notice BIONAIRE BPH1515-I

« YTTÖOPAS BRUKSANVISNINGBRUGERVEJLEDNING INSTRUKCJA

  ??????????? ?? ???????????? HASZNÁLATI UTASÍTÁSNÁVOD K OBSLUZE English2 Deutsch/German4 Français/French7 Español/Spanish9 Nederlands/Dutch12 Svenska/Swedish14 Suomi/Finnish16 Norsk/Norwegian19 Polski/Polish21 EKKHNIKA/Greek23 "esky/Czech26 Magyar/Hungarian28 PYCCKNÑ/Russian30 Italiano/Italian33 Português/Portuguese35 Dansk/Danish38 BPH1515I06MLM1.qxd 9/27/07 21:11 Page 1BPH1515 B A C H(r) I + - Fig.4Fig.3 Fig.6 Fig.1 Fig.2 D EF G H(l) Fig.5 Fig.7 RETAIN THE FOLLOWING FOR FUTURE REFERENCE. DESCRIPTIONS (SeeFig.1 & 2) A.Left End Cap B.Rear Housing C.Right End Cap D.Display E.Mode Indicator Lights F.Mode Button G.Thermostat Adjustment Buttons H.Foot Base (2) I.Grill Foot Assembly (See Fig.3) 1.Insert Left Foot Base H(l) into Left End Cap (A) and tighten the Screw. 2.Insert Right Foot Base H(r) into Right End Cap (C) and tighten the Screw. Wall Mounting Assembly (See Fig.4 - Fig.6) IMPORTANT:Before drilling into any wall ensure no electrical cables are present in the area. NOTE:Due to the multitude of potential mountingsurfaces, mounting screws are not included with this product.Please seek professional assistanceor visit your local hardware store to determine which type of screw is best for your particular wall. 1.Remove Base Feet (H) from the End Caps (A and C), if installed. 2.Secure the Mounting Bracket to the wall. 3.Hang the main body on the Mounting Bracket. SETTING THE ACCUTEMP PLUS™ THERMOSTAT 1.Press ( ) Mode button (F): • 1st= LO;runs continuously on low. • 2nd= HI;runs continuously on high. • 3rd= Auto Low;press (+) or (-) to set desired temperature. • 4th= Auto HI;press (+) or (-) to set desired temperature. 2.Once you have selected the mode and temperature, the display returns to the current room temperature and gradually increases as the room warms. 3.If you selected an Auto mode and the heater does not start, make sure the set temperature is higher than the current room temperature. NNOOTTEE:: In Auto mode,it is normal for the heater to cycle ON and OFF as it maintains the programmed temperature. To prevent the unit from cycling,raise the thermostat setting. The AccuTemp Plus™ Thermostat remembersthe previous temperature setting after the unit is turned off. However,ifthe unit is unplugged,the digital thermostat resets and no longer remembers the previous temperature setting. PROGRAMMABLE TIMER You can program your heater to turn on at a preset time or turn off after a set amount of time. Setting the On Timer: 1.With the heater off, press and hold (+) and (-) simultaneously until the display flashes. 2.Press (+) or (-) to select the amount of time you would like to pass before the heater turns on. 3.After setting the timer, the display shows a red dot next to the current room temperature on the display to indicate that the timer is activated. 4.After the programmed length of time has passed, the heater automatically turns on Auto HI at 24°C (75°F) for 2 hours. Setting the OffTimer: 1.Select the desired mode and/or temperature. 2.With the heater running, press and hold (+) and (-) simultaneously until the display flashes. 3.Press (+) or (-) to select the amount of time you would like the heater to run. 4.After setting the timer, the display shows a RED dot next to current room temperature on the display to indicate that the tim... »