Notice NUMARK TT1625

Notice NUMARK TT1625

Mode d'emploi NUMARK TT1625 disponible.

Groupe d'entraide des utilisateurs NUMARK TT1625

Bienvenue dans le groupe d'entraide des utilisateurs
NUMARK TT1625

Le groupe d'entraide NUMARK TT1625 vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Platine vinyle. Rejoignez GRATUITEMENT notre groupe d'entraide TT1625 pour vous aider à mieux utiliser votre Platine vinyle NUMARK. Le SAV entre consommateurs donne accès à différents services pour votre NUMARK TT1625 : accès à la notice TT1625 et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

NUMARK TT1625

Dernières actualités du groupe d'entraide NUMARK TT1625

Nouvelles questions du forum

Nouveaux avis

Nouveaux membres

  • nogopet376  depuis le 14/12/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)
  • crj3108@gmail.com  depuis le 02/11/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 1 068 K | Français

Pas de vidéo disponible

« (stereo) BOX CONTENTS - Turntable - Aluminum Platter with slipmat - Pre-mounted cartridge - Counterweight - 45 RPM adapter - IEC power cable -Stereo RCA cable(ENGLISH) QUICKSTART GUIDE 1. Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT 3. Go to http://www.numark.com for product registration. GENERAL CONTROLS 1. Power Cable: This power cable should be plugged into a wall receptacle AFTER all audio connections are made. 2. RCA Audio Output Cables: These cables are used to connect the turntable to a DJ mixer or amplifier that has a built in PHONO PREAMP. This RCA type input is a feature that is commonly found on most DJ mixers and will be labeled PHONO or TURNTABLE. If the RCA Audio Output Cables are not connected to a mixer or amplifier with a PHONO PREAMP, then the audio output will be very quiet. 3. Ground Wire: This ground wire must be connected to a metal bolt or ground lug that is on the mixer or amplifier that the turntable is connected to. If the ground wire is not securely fastened to a metal bolt or ground lug, then the audio output will exhibit a “buzzing” sound. 4. Power Button: Turn on and turn off the machine with this button. 5. Platter: This aluminum platter must be securely fastened to the turntable prior to operation. See SETUP INSTRUCTIONS for detailed information on installing the platter. 6. Start/Stop Buttons: These buttons start and stop the turntable motor. Both buttons have the same function. If they seem to not be functioning, check to make sure that the platter is properly installed in the SETUP INSTRUCTIONS. 7. 33 and 45 RPM Buttons: These buttons control the RPM of the turntable platter. A red LED indicates which RPM mode has been selected. NOTE: If the turntable is powered down while in the 45 RPM setting, it will return to 33 RPM when it is powered up. 8. Pitch LED: This LED illuminates green when the pitch slider is set at 0%. When the pitch slider is moved away from zero, the LED illuminates red. 9. Pitch Slider: This slide control allows the pitch to be increased or decreased by 10%. In the center position the pitch is at 0%. When moved away from the center and towards the tone arm decreases the pitch (slows down the platter) and moving the pitch slider away from the tone arm increase the pitch (speeds up the platter.) TONE ARM: Items 10 – 13 are all parts of the Tonearm. Refer to the TONEARM SETUP section for additional details on these controls. Your model will be equipped with straight arm or S-arm style depending upon model purchased. 10. Counter Weight and Scale Ring: The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 11. Anti-Skate Adjustment: This knob is used to compensate for inward tracking forces. See TONEARM SETUP for more details. 12. Arm Clip: This specially designed arm clip secures the tone arm while at rest or when not in use. The arm clip has been designed to remain in the up position while unlocked. NOTE: When transporting the turntable, it is always recommended that the headshell be removed and the arm clip secured to prevent tonearm or turntable damage. 13. Cartridge and Headshell: The cartridge is pre-mounted on a standard headshell. The cartridge is user replaceable and compatible with a v... »

Activité de ce groupe d'entraide

Note moyenne du groupe
4 étoiles
Durée moyenne d’utilisation
Avis consommateur
2 avis
Aucune opinion sur NUMARK
Donner votre opinion sur NUMARK

Découvrez nos autres catégories :

En cours...