Notice Rosières RHI693SPIN

Notice Rosières RHI693SPIN

Mode d'emploi Rosières RHI693SPIN disponible.

Groupe d'entraide des utilisateurs Rosières RHI693SPIN
7 membres dans ce groupe pour vous aider
Trouver de l'aide en rejoignant le Groupe d'entraide des
utilisateurs de votre produit RHI693SPIN

Bienvenue dans le groupe d'entraide des utilisateurs
Rosières RHI693SPIN

Besoin d'aide pour l'utilisation de votre Rosières RHI693SPIN ? Le groupe d'entraide Rosières RHI693SPIN vous donne des conseils d'utilisation, solutions aux problèmes d’entretien, fonctionnement et assistance pour votre Hotte. Rejoignez notre groupe d'entraide RHI693SPIN qui compte 7 membre(s). L'inscription GRATUITE vous donne accès à différents services pour votre Hotte : accès à la notice RHI693SPIN et mode d'emploi pdf Rosières RHI693SPIN, manuel d'utilisation en français, 2 avis consommateur et 1 discussion(s) de forum actif comprenant 1 participant(s), guide de l'utilisateur, photos, vidéos et SAV entre consommateurs.

Dernières actualités du groupe d'entraide Rosières RHI693SPIN

Nouvelles questions du forum

Nouveaux avis

Nouveaux membres

  • papa1502  depuis le 30/06/2017 - Expertise débutant - Utilisateur depuis moins d'un mois
  • Cocovel  depuis le 11/09/2014 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 744 K | Français
Site Web Marque | Français

Pas de vidéo disponible

« e filtering version, a charcoal filters and an air baffle (Fig. 1A) must be used, which placed at the top of the structure, allows the air to recycle back into the room. In the Ducting version, cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2). INSTALLATION ATTENTION: Three people are required for proper installation; the unit should be installed by a qualified operator. Also follow carefully each step of the assembly instructions, and once installation has been completed, make sure that the hood is firmly secured in place. For assembling it is essential to: – Prepare the connection to the mains within the telescopic structure. – If your unit is installed in a ducting hood, prepare the air exhaust hole. Ductng version: - When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which vary from nation to nation) and is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section (diameter: 150 mm). - Using the drilling jig make the holes for fixing to the ceiling on the vertical line of your hob; carefully follow all the indications for final positioning of the hood. Bear in mind that one of the axes of the drilling jig must correspond to the axis of the hood controls. Secure the telescopic structure to the ceiling using the screws and screw anchors provided (Fig. 3); Pay attention as positioning of the structure determines the final position of the hood: the opening B must be at the front. - Adjust the height of the telescopic structure with the 8 retaining screws C (Fig. 4); To determine the height (H) of the telescopic structure, refer to the measurements indicated in Fig. 5 bearing in mind that the distance between the hood and the hob must be at least 650 mm. - Connect the air exhaust pipe to the metal flange (D) on the inside of the telescopic structure (Fig. 6). - Take the flange with valve (E) and fit it to the air vent of the hood, exercising slight pressure (Fig. 7). - Take the upper part of the hood (pipe with slots) and fit it on the telescopic structure with the slots at the bottom (Fig. 8); Secure it to the telescopic structure with 2 screws. - Take the lower part of the hood, open the metal panel and remove the grease filter (Fig. 9). Secure the lower part of the hood to the upper part, inserting the 4 pins (F) in the holes and lock everything with 4 nuts and 4 washers (Fig. 10) working from the inside of the hood. - Make the electrical connection by means of the power cable. At this point, installation has been completed and the grease filter can be fitted. Filtering version: - Using the drilling jig make the holes for fixing to the ceiling on the vertical line of your hob; carefully follow all the indications for final positioning of the hood. Bear in mind that one of the axes of the drilling jig must correspond to the axis of the hood controls. - Separate the upper from the lower telescopic structure by removing the screws (C) and washers (Fig. 4). - Insert the air baffle (G) in the upper telescopic structure (Fig. 11). - Fit the flange (L) on the baffle (Fig. 11) and connect a flexible hose locking it with a metal clamp (hose and clamp are not provided). - Secure the upper telescopic structure to the ceiling using t... »

Activité de ce groupe d'entraide

Note moyenne du groupe
3 étoiles
Durée moyenne d’utilisation
6 ans
Avis consommateur
2 avis
Aucune opinion sur Rosières
Donner votre opinion sur Rosières
En cours...