Notice PIONEER CP81BMK

Notice PIONEER CP81BMK

Mode d'emploi PIONEER CP81BMK disponible.

Groupe d'entraide des utilisateurs PIONEER CP81BMK

Bienvenue dans le groupe d'entraide des utilisateurs
PIONEER CP81BMK

Le groupe d'entraide PIONEER CP81BMK vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Autoradio. Rejoignez GRATUITEMENT notre groupe d'entraide CP81BMK pour vous aider à mieux utiliser votre Autoradio PIONEER. Le SAV entre consommateurs donne accès à différents services pour votre PIONEER CP81BMK : accès à la notice CP81BMK et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

Dernières actualités du groupe d'entraide PIONEER CP81BMK

Nouvelles questions du forum

Lancez la discussion

Nouveaux membres

  • nogopet376  depuis le 15/12/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 5 265 K | Français

Pas de vidéo disponible

« from the stand, and then move the stand, holding it by the stems. •Place the stand on a stable, level surface; placing the stand on an unstable surface can be dangerous. •Pioneer assumes no liability whatsoever for damages resulting from assembly, improper mounting, insufficient reinforcement, misuse of the product, acts of nature, etc. Names of Parts Screw holes for securing speaker Speaker support Stand stems Stand base FRRD-235-A_CP-81_En.book 2 ??? 2008?7?24? ??? ??2?15?3 En English Attaching speakers to the stands A medium Phillips screwdriver is required for assembling the speaker stand and for attaching the speaker. Assembling the speaker stands Assemble the speaker stands as illustrated below. Align the screw holes on the stand base and speaker support with the screw holes in the three stems, then insert the screws and tighten. •Make sure you assemble the stand on a flat surface that is relatively soft (such as a carpet). •Make sure the screws are inserted in the screw holes as shown above (with the screw head hidden) when securing the speaker. Improper setup could result in damage or injury if the speaker falls from the stand. When using the spikes This speaker stand includes spikes that you can use to isolate the speaker from the floor. Spikes are recommended when placing the stand on a thick carpet (for added stability), or for better sound when placing the stand on a hard reverberant surface (such as a concrete or wood floor). Use the supplied spike bases to avoid scratching the floor or other surface where the stand is placed. 1Twist the spikes into the threaded metal inserts embedded in the bottom of the stand base. 2Set the spike bases in the positions where the points of the three spikes will strike when the speaker stand is set down. 3Set the speaker stand on the spike bases and check to confirm the speaker stand does not rock. •Note that these spikes are sharp metal and can cause damage to flooring. Make sure to lay down a cloth or suitable base before setting up. •Always use the spike bases as shown, with the indented surface facing up to receive the spike point. When using the non-skid pads 30 mm (1 3/16 in.) Black 30 mm (1 3/16 in.) Black Speaker support Stand stems Stand base Spikes [SBA6080] Spike bases [SBG6001] Screws (Bind head, M6 x L30) [SBA6089] Screws (Bind head, M6 x L30) [SBA6089] Please note that sunken screw holes are provided in the speaker support. If you do not use the spike bases when placing the speakers, the spikes may cause damage to the floor. If you plan on using the spikes we highly recommend to use the spike bases. Stand base Stand base FRRD-235-A_CP-81_En.book 3 ??? 2008?7?24? ??? ??2?15?4 En When using speaker spikes: To avoid accident or injury, please use screws to secure the speaker to the speaker stands. Note that there are fastening nuts provided on the speaker base (see below). Secure the speaker to the speaker support using the washer, spring washer and the 50 mm (2 in.) screws as shown below. When not using speaker spikes: To avoid accident or injury, please use screws to secure the speaker to the speaker stands. Note that there are fastening nuts provided on the speaker base (see below). Secure the speaker to the speaker support using the washer, spring washer and the 40 mm (1 5/8 in.) screws as shown below. 50 mm (2 in.) Black Speaker support F... »

Activité de ce groupe d'entraide

Note moyenne du groupe
Soyez le premier à noter ce produit
Durée moyenne d’utilisation
Pas d'avis consommateur
Donnez votre avis
Aucune discussion
Lancez la discussion !
Aucune opinion sur PIONEER
Donner votre opinion sur PIONEER

Découvrez nos autres catégories :

En cours...