Notice EPSON TM T70

« ssion speed Transmission speed (bps)-bits per second1-71-8 Adjustable by control commands (default: 115200) ONON 4800OFFON 9600ONOFF 19200OFFOFF Serial Interface (DIP switch 2) SWFunctionONOFF 2-1Handshaking (BUSYcondition) Receive buffer full Offline or Receive buffer full 2-2Reserved (Do not change)–Fix to OFF 2-3 2-4 Selects print density/ Lowpower comsumption mode See Table A. 2-5Reserved–– 2-6Reserved (Do not change)–Fix to OFF 2-7I/F pin 6 reset signalEnabledDisabled 2-8I/F pin 25 reset signalEnabledDisabled Interface other than Serial (DIP switch 1) SWFunctionONOFF 1-1Auto line feedAlways enabled Always disabled 1-2Receives buffer capacity 45 bytes4K bytes 1-3Reserved–– 1-4Error signal outputDisabledEnabled 1-5~ 1-8 Reserved–– Interface other than Serial (DIP switch 2) SWFunctionONOFF 2-1Handshaking (BUSY condition) Receives buffer full Offline or receives buffer full 2-2Reserved (Do not change) –Fixed to OFF 2-3 2-4 Print density/ Lowpower See Table A. 2-5Reserved–– 2-6Reserved (Do not change) –Fixed to OFF 2-7I/F pin 6 reset signal (Do not change) EnabledDisabled 2-8I/F pin 31 reset (Do not change) EnabledDisabled Table A Print density/low powerSW 3SW 4 Print density (Standard)OFFOFF Print density (Darker than standard)ONOFF Print density (Dark)OFFON Low power consumption mode ONONv English Specifications Printing methodThermal line printing Dot density180 dpi × 180 dpi [dots per 25.4 mm {1"}] Printing directionUnidirectional with friction feed Printing width72.2 mm {2.84"}, 512 dot positions Characters per line (default) Font A: 42, Font B: 56 Character spacing (default) Font A: 0.28 mm {.01"} (2 dots); Font B: 0.28 mm {.01"} (2 dots) Character sizeStandard/Double-height/Double-width/Double-width and Double-height Font A: 1.69 × 3.38 mm/1.69 × 6.77 mm/3.38 × 3.38 mm/3.38 × 6.77 mm Font B: 1.27 × 2.40 mm/1.27 × 4.79 mm/2.54 × 2.40 mm/2.54 × 4.79 mm Number of charactersAlphanumeric characters: 95; International characters: 48 Extended graphics: 128 × 11 pages (including user-defined page) Printing speed High-speed mode: 170 mm/s {6.69"/s} max.; 40.2 lps (4.23 mm {1/6"} feed) Ladder bar code and 2D code: 100mm/s {3.9"/s} Low-power consumption mode: 150 mm/s {5.91"/s} max.; 35.5 lps (4.23 mm feed {1/6"}) Bit image, Ladder bar code, 2D code and Page mode: 60mm/s {2.4"/s} The above speed values are approximate. The values are when the printer prints with density "Normal" at 24 V and 25°C {77°F} Speed is adjusted automatically depending on the voltage applied and head temperature. Paper feed speedApprox. 170 mm/s {approx. 6.69"/s} continuous paper feed Line spacing (default)4.23 mm {1/6"} Character structureFont A: 12 × 24, Font B: 9 × 17 Font A is the default. Roll Paper (single-ply)Size:79.5 mm ± 0.5 mm {3.13" ± 0.02"}, Maximum outside diameter:83 mm {3.27"} Roll Paper spool diameter:Inside: 12 mm {0.47"}; Outside: 18 mm {0.71"} Thermal paper typeSpecified: NTP080-80 Interface (compatible) Serial (RS232/RS485)/Parallel (IEEE1284)/USB/EPSON UB series Receive buffer4KB/45 bytes DKD Function2 drives Supplied voltage+ 24 VDC ± 7% Current consumption (at 24V) High-speed mode:Mean: Approx. 1.8 A Low-power consumption mode:Mean: Approx. 1.2 A LifeMechanism:15,000,000 lines Thermal head:100 million pulses, 100 km Autocutter:1,500,000 cuts MTBF360,000 hours MCBF52,000,000 lines (Average fai... »