Notice NUMARK PT01

Notice NUMARK PT01

Mode d'emploi NUMARK PT01 disponible.

Groupe d'entraide des utilisateurs NUMARK PT01
35 membres dans ce groupe pour vous aider
Trouver de l'aide en rejoignant le Groupe d'entraide des
utilisateurs de votre produit PT01

Bienvenue dans le groupe d'entraide des utilisateurs

Besoin d'aide pour l'utilisation de votre NUMARK PT01 ? Le groupe d'entraide NUMARK PT01 vous donne des conseils d'utilisation, solutions aux problèmes d’entretien, fonctionnement et assistance pour votre Platine vinyle. Rejoignez notre groupe d'entraide PT01 qui compte 35 membre(s). L'inscription GRATUITE vous donne accès à différents services pour votre Platine vinyle : accès à la notice PT01 et mode d'emploi pdf NUMARK PT01, manuel d'utilisation en français, 1 avis consommateur et 2 discussion(s) de forum actif comprenant 3 participant(s), guide de l'utilisateur, photos, vidéos et SAV entre consommateurs.


Dernières actualités du groupe d'entraide NUMARK PT01

Nouvelles questions du forum

Nouveaux membres

  • DylanL9533  depuis le 24/10/2016 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)
  • AnnesophieL9676  depuis le 12/10/2016 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 909 K | Français

Pas de vidéo disponible

« ote: This turntable can be used as a standalone unit, as well as with the items listed in the quick setup diagram. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo output devices to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into power. 9. Switch everything on in the following order. •Turntable •Mixer (not included) •last, any amplifiers or output devices (not included) 10. When turning off, always reverse this operation by, •turning off amplifiers (not included) •mixer (not included) •Turntable 11. Go to for product registration. More information about this product may be found at BATTERY INSTALLATION This product can be powered by 6 “D” Cell batteries. They should be loaded as show above, with the positive end toward the handle.PRODUCT FEATURES 1. Platter: Place your record on the platter. 2. Control Panel: Please see the alternate detailed section on the control panel features. 3. On Board Speaker: Use this speaker to listen to the audio. 4. Tone Arm Clip: Use this clip to secure your tonearm when storing and transporting the unit. 5. Tonearm: This unit comes with a ready to use pre- balanced tonearm and cartridge. The cartridge is user replaceable with parts from your distributor located in the warranty guide. The platter starts spinning once the tonearm is lifted over the record. 6. 45 Adapter: Use this adapter with 45 rpm records. 7. Dust Cover: This cover protects the turntable from dust and abuse while not in use or while in transport. 8. Dust Cover Latch: This latch holds the dustcover securely in place, and can easily be opened by sliding it to the left. 9. Carry Handle: Use this handle easily remove the unit from record crates and bags, as well as carrying it in transport. 10. Battery Cover: This holds the batteries securely in place during use and transport. It easily slides open and closed as indicated on the cover itself. NOTE: This unit uses 6 “D” cell batteries (not included). They should be installed in the proper direction indicated OUTPUT PANEL 1. Power Switch: Use this switch to turn the power on and off. 2. AC In: This turntable is designed to work with either batteries or the power supply cord that comes with it. While the power is switched off, plug the power supply into the turntable first, then plug it into the wall power outlet, then switch on. NOTE: This unit can also be powered by 6 “D” Cell batteries (Not Included). 3. Master Output (RCA): This “line level” output is for connecting to the input of an external audio device such as a DJ mixer, tape recorder, CD Burner, PA system, powered speaker, or a home stereo. The level of the master stereo output signal is controlled by the audio level control. 4. 1/8” Headphone Jack: Use this jack with the 1/8” mini headphone plug. NOTE: Be sure the volume control is set to the OFF position before plugging in any headphones to avoid permanent hearing damage. 5. 1/4” Headphone Jack: Use this jack with the 1/4” headphone plug. NOTE: Be sure the volume control is set to the OFF position before plugging in any headphones to avoid permanent hearing damage. POWERPITC... »

En cours...