Notice AXIS 216FD-V

« sing AXIS 216FD-V: vandal-resistant casing AXIS 216MFD: tamper-resistant casing AXIS 216MFD-V: vandal-resistant casing PS-H indoor power supply (country specific) Europe UK Australia USA/Japan Argentina Korea Power supply extension cable1.8 meters Terminal block connector 4-pin connector block for connecting external devices to the I/O terminal connector Mounting kitScrewdriver for tamper-proof screws Tamper-proof screws Drill template CDAXIS Network Video Product CD, including product documentation, installation tools and other software Printed MaterialsAXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide (this document) Axis Warranty Document Important! This product must be used in compliance with local laws and regulations.Page 4AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Hardware overview Product ID & Serial number (S/N). The serial number may be required during the installation. Dimensions HxWxD = 94 x 144 x 132mm (3.7" x 5.7" x 5.2") Weight AXIS 216FD/AXIS 216MFD = 425g (0.94 lb) (power supply not included) Weight AXIS 216FD-V/216MFD-V = 580g (1.28 lb) (power supply not included) Cover plates Network indicator LED Status indicator LED Control button Power connector (see page14) Network connector (see page14) I/O terminal connector (see page14) Power indicator LED Audio out Audio in Microphone 16mm cable conduit (not supplied) fitted to AXIS 216FD-V/216MFD-VAXIS 216FD/216FD-V/216MFD/216MFD-V Installation GuidePage 5 ENGLISH ENGLISH Install the hardware Mount the camera The AXIS 216FD/216FD-V/216MFD/216MFD-V can be mounted with the cables routed through the wall/ceiling, or from above or below. There are cover plates for the openings on both sides of the dome cover. The AXIS 216FD-V/216MFD-V can also be fitted with a metal conduit for protecting the cabling when connected via the side openings. See the illustrations on page4. 1.Using the drill template, drill two holes in the ceiling/wall. 2.Route and connect all the required cables. See Connect the cables, below. 3.Fasten the camera unit to a ceiling or wall, using screws and plugs appropriate for the ceiling/wall material. 4.Ensure the camera is positioned so that the tamper-proof screws can be tightened using the supplied screwdriver. Mounting on a hard ceiling To mount the AXIS 216FD/216FD-V/216MFD/216MFD-V on a hard ceiling, check that the ceiling material is sturdy enough to hold the weight of the camera. The camera can also be secured using a plate or board that better carries the weight of the camera, and which is more suitable for securing the screws. The AXIS 216FD/AXIS 216MFD can also be mounted using the AXIS 216FD/AXIS 216MFD Drop Ceiling Mount, which allows the camera to be mounted more discreetly. Please see www.axis.com for all available mounting accessories. ! IMPORTANT! - The casing of the AXIS 216FD/216FD-V/216MFD/216MFD-V is not approved for outdoor use - the product may only be installed in indoor environments. Plate or Hard ceiling AXIS 216FD/216FD-V Screws board 216MFD/216MFD-VPage 6AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Connect the cables 1.Connect the camera to the network using a shielded network cable. 2.Optionally connect external input/output devices, e.g. alarm devices. See page14 for information on the terminal connector pins. 3.Optionally connect an active speaker and/or external microphone. 4.Connect power,... »