Notice BROAN HI160I

Notice BROAN HI160I

Mode d'emploi BROAN HI160I disponible.

Groupe d'entraide des utilisateurs BROAN HI160I

Bienvenue dans le groupe d'entraide des utilisateurs
BROAN HI160I

Le groupe d'entraide BROAN HI160I vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Hotte. Rejoignez GRATUITEMENT notre groupe d'entraide HI160I pour vous aider à mieux utiliser votre Hotte BROAN. Le SAV entre consommateurs donne accès à différents services pour votre BROAN HI160I : accès à la notice HI160I et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

Dernières actualités du groupe d'entraide BROAN HI160I

Nouvelles questions du forum

Nouveaux membres

  • Moumouth18  depuis le 16/09/2023 - Expertise débutant - Utilisateur depuis plus de 5 ans
  • BeachBob  depuis le 25/06/2023 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Pas d'image disponible

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 1 300 K | Français

Pas de lien disponible

Pas de vidéo disponible

« ng version the air and the kitchen fumes that are conveyed by the apparatus are depurated by the charcoal filter and put back into the room through the small grilles of the ventilation flue (Fig. 1). ATTENTION: When using the filtering version, a charcoal filter and an air baffle (Fig. 1A) must be used, which placed at the top of the structure, allows the air to recycle back into the room. In the Ducting version, cooking vapours and odours are conveyed straight outside by a disposal duct which passes through the ceiling (Fig. 2). INSTALLATION ATTENTION: 3 persons are required for proper installation; the unit should be installed by a qualified operator. Also follow carefully each step of the assembly instructions, and once installation has been completed, make sure that the hood is firmly secured in place. Before proceeding with assembly operations and to ensure easier manoeuvrability of the appliance, disengage the grease filter: push the handle outwards and pull the filter downwards. 3). Also remove the metallic surround by removing the 4 retaining screws (Fig. 4). Separate the upper part of the telescopic structure from the lower part by removing the 4 retaining screws and the 4 washers (Fig. 5). Essential requirements for assembly: – Prepare electricity supply inside the the telescopic flue – If your appliance is to be installed as a Ducting version, prepare the air evacuation hole. When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which vary from nation to nation) and iv) is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section (diameter: 150 mm). ASSEMBLY Ducting version: Using the specific drilling template, make holes for fixing to the ceiling in the vertical part of your cooking top; observe all indications for the final positioning of the appliance. Bear in mind that one of the two axes of the template must correspond with the axis of the extractor hood controls. Secure the upper part of the telescopic structure to the ceiling using the 4 screws and pads supplied (Fig. 6); pay close attention since the positioning of the structure determines the final position of the extractor hood. During this operation, pass the air air evacuation pipe inside the telescopic structure and the electricity supply through the specific hole in the structure (Fig. 6). Fit the adapter flange on the air output mouth of the motor. 7). Secure the motor unit to the lower telescopic structure, using 4 nuts and 4 washers (Fig. 8). This block should then be secured to the upper telescopic structure (Fig. 9) previously secured to the ceiling (with the 4 screws and 4 washers removed previously). Adjust the height of the telescopic structure using the four screws (Fig. 9) bearing in mind that the extractor hood must be at minimum distance of 650 mm from the cooking top. (Fig.10). Through the apertures in the telescopic structure, secure the air evacuation pipe to the adapter flange using a band (Fig.11); the pipe and band are not supplied. Make the electrical connection using the power supply cable. Take the upper flue (the one with slots) and insert it into the telescopic structure, with the slots at the bottom; secure it to the structure with 2 screws (Fig. 12). Take the lower flue and insert it in the same... »

Activité de ce groupe d'entraide

Note moyenne du groupe
3 étoiles
Durée moyenne d’utilisation
Avis consommateur
15 avis
Aucune opinion sur BROAN
Donner votre opinion sur BROAN
En cours...