Notice BROAN HD1000I

Notice BROAN HD1000I

Mode d'emploi BROAN HD1000I disponible.

Groupe d'entraide des utilisateurs BROAN HD1000I

Bienvenue dans le groupe d'entraide des utilisateurs
BROAN HD1000I

Le groupe d'entraide BROAN HD1000I vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Hotte. Rejoignez GRATUITEMENT notre groupe d'entraide HD1000I pour vous aider à mieux utiliser votre Hotte BROAN. Le SAV entre consommateurs donne accès à différents services pour votre BROAN HD1000I : accès à la notice HD1000I et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

BROAN HD1000I

Dernières actualités du groupe d'entraide BROAN HD1000I

Nouvelles questions du forum

Nouveaux membres

  • dadilosa  depuis le 02/03/2024 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)
  • GulGreg  depuis le 15/08/2022 - Expertise débutant - Utilisateur depuis plus de 5 ans

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 1 442 K | Français

Pas de lien disponible

Pas de vidéo disponible

« reater efficiency, we recommend you install the hood in the ducting version (if possible). INSTALLATION ATTENTION: Two persons are required for proper installation; the unit should be installed by a qualified operator. Remove the grease filters before proceeding with the assembly instructions. This will make the appliance easier to handle. 1.Removal of grease filters (refer to Figure 3, 4 or 5 depending on model purchased): Fig.3-4: press the lock towards the back part of the device and rotate the filter low. Fig.5: press the 2 locks inside the device and remove the metallic shelf bending slightly. INSTALLATION IN DUCTING VERSION: Before fixing, the outlet pipe for air evacuation to the outside must be installed. Use an outlet pipe with: – minimum indispensable length; – minimum possible bends (maximum angle of bend: 90°); – certified material (according to the State); – an as smooth as possible inside. It is also advisable to avoid any drastic changes in pipe cross-section (we suggest a chimney with a 125 mm diameter for the K18E1and K19E1 models; instead for the K18S1 and K18S1 models we suggest a chimney with a 150 mm diameter. For the model type, make reference to the technical plate inside the device). For air evacuation to the outside, follow all the other instructions given on the “Warnings” sheet. Prepare the power supply within the telescopic chimney (for the electrical connection, follow all the other instructions on the “Warnings” sheet). 2.Fixing to the wall: Draw a line on the wall in vertical line with your hob. Mark the first 4 holes (ø 8 mm) to be drilled in the wall, respecting the distances indicated in Fig.6. Important: before to make holes, please ensure that the drilling is perfectly aligned horizontally and vetically by using a level. Drill the holes and fit the screw anchors provided. As already specified on the “Warnings” sheet, bear in mind that the distance between the lower edge of the hood and the hob must be min. 650 mm. Insert two of the supplied screws so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance (Fig. 7A). Once the apparatus is hooked, fix it definitively to the wall using the two other screws and the holes made at its bottom (Fig. 7B). 3.Flange assembly: According to the model you purchased, proceed as follows: -flange assembly ø125 mm (Fig.8): make the 3 locks coincide with the 3 buttonholes and rotate the flange. -flange assembly ø 150 mm (Fig.9): set the flange over the motor air grilles and press slightly. 4.Securing the telescopic flue: Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches on the centre of the bracket (Fig.10); using a pen, mark the 2 holes on the wall and then make the holes and fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided). Take 2 assembled flues and place these on the upper surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.11). INSTALLATION IN FILTERING VERSION: Prepare the power supply within the telescopic flues (for the electrical connection, follow all the other instructions on the “Warnings” sheet). Fixing to the wall: for fixing to the wall refer to the instructions for the ducting version (see points 2, 3), then continue with the instructions below. Securing the telescopic flue: Place bracket (W) 50... »

Activité de ce groupe d'entraide

Note moyenne du groupe
3 étoiles
Durée moyenne d’utilisation
Avis consommateur
4 avis
Aucune opinion sur BROAN
Donner votre opinion sur BROAN
En cours...