Notice FUJITSU Siemens ScenicView E19W-1

« Visible diagonals: 48 cm (19”) Screen size : 410 mm x 256 mm Dimensions (W x H x D) incl. monitor base : 446 mm x 364mm x 214 mm Dimensions box (W x H x D): 510 mm x 440 mm x 145 mm Weight : approx. 4.6 kg / 5.9 kg Dot pitch : 0,285 mm Maximal resolution : 1440 x 900 pixels Electical data Video: analogue, positiv, 0.7 Vpp, 75 O digital,DVI(optional) Synchronisation : Seperate Synch. TTL, positive or negative Horizontal frequency: 31 kHz …. 83 kHz Refresh rate: 56 Hz …. 75 Hz Maximum pixel rate: 140 MHz Power supply: switches automatically 100 V – 240 V, 50 Hz – 60 Hz, 1.0 A max. Total power consumption: < 50 W < 2 W in the energy-saving modes (standby mode, suspend mode and Off mode) Environmental conditions Environment class 3K2, IEC 721 Operating range: 5 °C …. 35° C Humidity: 20 % …. 85 % Condensation must be avoided. Preset operating modes The picture position and size have been set set to optimum values at the factory for the operating modes listed above. Horizontal frequency Refresh rate Display resolution 31.5 kHz 31.5 kHz 37.5 kHz 37.9 kHz 46.9 kHz 48.4 kHz 60.0 kHz 64.0 kHz 79.9 kHz 56.0 kHz 70.6 kHz 70 Hz 60 Hz 75 Hz 60 Hz 75 Hz 60 Hz 75 Hz 60 Hz 75 Hz 60 Hz 70 Hz 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1440 x 900 1440 x 900 Using the Display Turning On the Display Turn on the display before turning on the computer. When the power is on, the LED on the power button lights blue and the screen image will appear after about 10 seconds. If the LED doesn’t light blue or no image appears, please verify if the display is properly connected. Function Controls 1,2 < > Hot key & Left / Decrease & Right / Increase OSD Off: Press < open “BRIGHTNESS” and “CONTRAST ” menu. Press > directly to adjust the volume.(only monitors with audio input) OSD On: Usethese buttons to select or adjust the values of the selected function. 3 MENU Hot key & SELECT OSD Off: Open OSD OSD On: Select function. (submenu) 4 AUTO Hot key & EXIT OSD Off: Auto adjustment function. OSD On: Exit OSD. 5 POWER Power Switch Power On/Off Blue-Operation mode / Orange-Power saving mode OSD Selection After you press the MENU button to enter the OSD menu, use < > to select the items you want to adjust. Then press the MENU button. After the screen fonts turn from blue to yellow you may start to make the adjustments. Just use < > to adjust the screen parameters as required. If no action is taken for 45 seconds after the setting, the system will automatically save your settings and exit the OSD. OSD Menu BRIGHTNESS/CONTRAST ADJUSTMENT: BRIGHTNESS: Adjusts brightness by using the buttons < or >. CONTRAST: Adjusts screen contrast by using the buttons < or >. IMAGE CONTROL: AUTO ADJUSTMENT: Automatically selects the optimal settings for image parameters (image position, phase, etc.) by using the button MENU. H. POSITION: Controls the picture’s horizontal position. V. POSITION: Controls the picture’s vertical position. CLOCK: Sets up the internal clock. Larger values make the displayed image appear wider; smaller values make it appear compressed. PHASE: Adjusts the internal clock’s time lag i... »