Notice Rosières RHT62RB

Notice Rosières RHT62RB

Mode d'emploi Rosières RHT62RB disponible.

Groupe d'entraide des utilisateurs Rosières RHT62RB

Bienvenue dans le groupe d'entraide des utilisateurs
Rosières RHT62RB

Le groupe d'entraide Rosières RHT62RB vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Hotte. Rejoignez GRATUITEMENT notre groupe d'entraide RHT62RB pour vous aider à mieux utiliser votre Hotte Rosières. Le SAV entre consommateurs donne accès à différents services pour votre Rosières RHT62RB : accès à la notice RHT62RB et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

Dernières actualités du groupe d'entraide Rosières RHT62RB

Nouvelles questions du forum

Nouveaux membres

  • nogopet376  depuis le 15/12/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)
  • DavidRedouté  depuis le 17/10/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 192 K | Français
Site Web Marque | Français

Pas de vidéo disponible

« union for the air to be scavenged. Use only motors proposed in the original catalogue. According to the model you have bought, the appliance can include 1 or 2 motors. In the I motor version the flange for the air to be exhausted has not got a central position, but it is slightly on the left. INSTALLATION Before assembling, in order to manoeuvre the appliance more easily, take off the grease grille (Fig. 4): pull the front of the grille upwards; desinsert the back from its seat. IMPORTANT: So as not to damage your product, during installation USE ONLY THE SCREWS PROVIDED. Make sure these are used as shown in the following instructions. To compensate possible depth voids between the appliance and the wall, a plastic SPACING BAR to be fixed at the back of the appliance by means of the three screws A is included (Fig. 5). The 3 screws A to be used are contained in the accessory bag attached to the plastic spacing bar. Cut the spacing bar according to the distance to be adjusted. ASSEMBLY UNDER A PENSILE CUPBOARD: The following operations are essential for assembly: – Install the wiring system; – Prepare the air venting hole if your appliance is to be installed in the ducting version or in the version with an external motor. In the Ducting version and in the version with an External motor, to get optimal conditions the air venting pipe should: – be as short as possible. – have the lowest number of bends (max bende angle: 90°). – be made of material approved by local authorities (according to the State). – have its inner side as regular and smooth as possible. It is moreover recommended to avoid drastic changes of pipe cross section (recommended diameter: 125 mm). Fixation as indicated in Fig. 6: Using the relative template make the 4 necessary fixing holes in the bottom of the cupboard and cut the air venting hole. For the version with an External motor, make the electrical connection between the hood and the external motor by means of the proper terminal board (Fig. 7): take off the cable clamp A and the cover B of the wiring junction box; fix the connection cable of the motor onto the terminal board C; reassemble the cable clamp A and the cover B of the junction box; the other end of the cable must be fixed onto the terminal board of the external motor. Move the hood close to the bottom of the wall unit and then connect the two units by means of the 4 self- tapping screws supplied together with the appliance. Fixation with brackets as in Fig. 8 (optional): Take the two brackets (S) out of the accessory bag together with the 8 screws provided. Fit the brackets to the wall unit being careful to position these correctly; for this operation use the 4 longer screws. At this point, secure the appliance to the brackets using the 4 shorter screws. Ducting version and version with an External motor: connect the flange of the hood with the air venting hole made previously in the wall/ceiling by means of an adequate tube. Make the electrical connection of the hood by means of the power supply cable. Assemble the anti-grease grille with the hood, inserting it obliquely (making the front side go upwards). Filtering version: connect a proper pipe to the flange of the hood so that the air is sent outside the pensile and sent back into the room. Make the electrical connection of the hood by means of the power supply cable. Set the fiber panel inside the anti-grease grille blocking it by means of the 2 supplied metal w... »

En cours...