Mode d'emploi PIONEER CP2EX disponible.

Groupe d'entraide des utilisateurs PIONEER CP2EX
1 membre dans ce groupe pour vous aider
Trouver de l'aide en rejoignant le Groupe d'entraide des
utilisateurs de votre produit CP2EX

Bienvenue dans le groupe d'entraide des utilisateurs

Le SAV entre consommateurs du groupe d’entraide PIONEER CP2EX vous permet de recevoir des solutions aux problèmes d’utilisation, conseils d’entretien, fonctionnement et assistance pour votre Autoradio PIONEER. Rejoignez GRATUITEMENT le groupe d'entraide CP2EX qui compte 1 membre(s) utilisateur(s) de ce produit. Devenir membre vous donne accès à différents services gratuits pour votre Autoradio : accès au mode d'emploi PDF et à la notice CP2EX en français PIONEER CP2EX, guide de l'utilisateur, avis consommateur et forum actif, manuel d’utilisation, photos, vidéo et informations.

Dernières actualités du groupe d'entraide PIONEER CP2EX

Nouvelles questions du forum

Lancez la discussion

Nouveaux membres

  • JeanJean1766  depuis le 28/11/2018 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 894 K | Français

Pas de vidéo disponible

« angerous. When placing the speaker, keep in mind that the tone is affected by the position of the speaker. If the bass is insufficient, move the speaker closer to the wall. The richest bass sound is obtained when the speaker is right against the wall. If the bass is too powerful, producing a muffled tone, move the speaker away from the wall. Placing the speaker against a thick curtain may also be effective. 50 cm20 cm Adjust the position as necessary to obtain optimal sound from your system. •Pioneer assumes no liability whatsoever for damages resulting from assembly, improper mounting, insuffi- cient reinforcement, misuse of the product, acts of nature, etc. Assembling the speaker stands Assemble the speaker stands as illustrated below. Please note that a flathead screwdriver will be necessary for assembly. The following illustration shows the fully assem- bled speaker stand: Screw holes for securing speakerSpeaker support Stand base Stand stems •Align the screw holes on the stand base and speaker support with the screw holes in the two stems, then insert the screws and tighten. Screws (Bind head, M6xL40) 40 mm Black Screws (Bind head, M6xL40) Nut Spike (SBA6053) Spike base(SLA1057) 40 mm Black Speaker support Stand base Stand stems Please note that sunken screw holes are provided in the speaker support. (SBA6054) (SBA6054) •Make sure you assemble the stand on a flat surface that is relatively soft (such as a carpet). •Make sure the screws are inserted in the screw holes as shown above (with the screw head hidden) when securing the speaker. Improper setup could result in damage or injury if the speaker falls from the stand.3 En English Using the spikes The speaker stands include spikes that you can use to isolate the speaker from the floor. Spikes are recommended when placing the stand on a thick carpet (for added stability), or for better sound when placing the stand on a hard reverberant surface (such as a concrete or wood floor). Use the supplied spike bases to avoid scratching the floor or other surface where the stand is placed. Spike1 2Nut Stand base plate 1Attach the spikes to the nuts provided. 2Attach all four spikes to the threaded metal inserts at the base of the speaker stand. 3Choose the location for speaker placement then put the spike bases on the floor. 4Place the stand so that the spikes are resting on the spike bases on the floor. Before placing the speaker on the speaker stand, make sure the stand is stable and resting squarely on all four spikes. •Note that these spikes are sharp metal and can cause damage to flooring. Make sure to lay down a cloth or suitable base before setting up. •The spike bases should be placed as shown below (with the depression on the top side). •Make sure to use the spike bases provided to avoid damaging the surface where you place the stand. Attaching speakers to the stands To avoid accident or injury, please use screws to secure the speakers to the speaker stands. Assembly with the S-2EX speaker system If you are using the S-2EX speaker system, note that there is a fastening nut provided on the speaker base (see below). When using speaker spikes: Place the speaker spike bases in the four holes provided on the speaker support, then secure the speaker to the speaker support using the washer, spring washer and the 62 mm screws as shown below. (SBA6050) Speaker base Speakersupport Washer (SBE6006) Spe... »

En cours...