Notice COLEMAN Event 14 Shelter

« e diagonally as shown and mark. d)Remove and stow corner locator for future use. (continued on other side)Fig. 1 To Set Up Shelter 1.Assemble Peak Pole with Center Hub. (Fig. 2) Fig. 2 Fig. 3 2.Assemble both Peak Connector Poles. (Fig.3) 4.Partially assemble the four Leg Poles with Ridge Hub. (Fig. 7) NOTE:Do not assemble the last pole on each side of the Ridge Hubs at this time. 3.Insert ends of the Peak Connector Poles marked with the arrows into the PeakPole with Center Hub. (Fig. 4, 5 & 6)Fig. 4Fig. 5 Fig. 6 Fig. 7 19’ 8” Fig. 9 5.Insert end of Peak Connector Pole into Ridge Hub (Fig. 8 & 9). Repeat for the remaing three Leg Pole with Ridge Hubs. NOTE:Make sure metal pin locks into slot on top of Ridge Hub, you may have to twist Peak Connector from side to side. SlotMetal Pin Peak ConnectorPole Fig. 8 Parts and Components DescriptionPart Number Peak Pole w/Center Hub (1)9391-1401 Peak Connector Poles (2)9391-1411 Leg Pole w/Ridge Hub (4)9391-1421 Pad Feet (4)9391-1451 Canopy (1)9391-1461 Peak Pole w/Center Hub (1) Leg Pole w/Ridge Hub (4)Pad Feet (4) Peak Connector Poles Center Hub Ridge Hub 14_EventShade-A4.qxd 10/10/06 11:30 PM Page 1Fig. 10 STITCH LINE The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219 1-800-835-3278 • www.coleman.com MADE IN CHINA• PRINTED IN CHINA ©2006 The Coleman Company, Inc. Coleman®and are registered trademarks of The Coleman Company, Inc. Things You Should Know: • Never store your shelter, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your shelter. Use a separate storage bag. • Stakes should be removed by pulling on the stake itself. Never pull on the canopy to remove stake. • SHELTER POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER DURING STORAGE. WARNING: Keep all flame and heat sources away from this shelter fabric. This shelter meets the flammability requirements of CPAI-84. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the shelter fabric may render the flame-resistant properties ineffective. To Set Up Shelter (continued) Fig. 11 7.Locate the hook & loop fasteners closest to the center of the under side of the canopy and wrap around poles to secure. (Fig. 11) 8.Position Pad Feet at the four corners (determined with the use of the Corner Locator in Step 1) as shown. (Fig. 12) NOTE:Pad Feet must angle in toward center of shelter with metal ring facing outward. Metal Ring Fig. 12 Fig. 13 9.Insert ends of Poles into Pad Feet and twist until metal pin locks into slot (Fig. 13). 10.Repeat for other three Pad feet locations. NOTE:Make sure the metal rings on the Pad Feet are facing out. Fig. 18Fig. 19 Fig. 15Fig. 16 Fig. 17 Angle faces inward MetalPin inslot 14.Attach hook end of Canopy tension strap to the metal ring on the Pad Feet. Repeat for the remaing three Pad Feet. Pull down strap, at each corner, to tighten. (Fig. 18 & 19) 13.Locate all velcro straps on the seams on the inside of the Canopy. Undo straps, wrap around Poles and secure tightly. (Fig. 17) 15.Attach Guy Lines to web loops located on outside seams of Canopy then secure with stakes. (Fig. 20) Fig. 14 Web Loop Guy Line Stake Fig. 20 Optional Sunwalls may be placed in any of the arched openings of the Shelter.... »