Notice SHARP LC19D1EBK

« (320,0) 218.0 (218,0) 40.0 (40,0) 240.0 (240,0) 100.0 (100,0) 100.0 (100,0) 17.5 (17,5) 232.4 (232,4) LC-19D1E/LC-19D1S [mm] SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or ASA and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: •The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. •The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that: •If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug. •The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires. IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.1 MODE D’EMPLOIFRANÇAIS Marques……………………………………………………………1 Cher client SHARP………………………………………………2 Précautions de Sécurité Importantes…………………………2 Accessoires fournis………………………………………………2 Guide rapide………………………………………………………3 Pose du socle…………………………………………………3 Mise en place du téléviseur…………………………………3 Insertion des piles……………………………………………4 Utilisation de la télécommande……………………………4 Précautions sur la télécommande……………………4 Télécommande………………………………………………5 Téléviseur (Vue frontale/latérale)……………………………6 Téléviseur (Vue de dos)………………………………………6 Mise sous tension……………………………………………7 Mode d’attente…………………………………………………7 Mise hors tension……………………………………………7 Auto installation initiale (Analogue)…………………………7 Auto installation initiale (DTV)………………………………7 Utilisation d’appareils externes…………………………………8 Raccordement d’un magnétoscope………………………8 Raccordement d’une console de jeu ou d’un caméscope………………………………………………8 Raccordement d’un lecteur DVD……………………………8 Raccordement d’un décodeur………………………………8 Raccordement d’un ordinateur………………………………9 Opérations du menu………………………………………………9 Opérations courantes…………………………………………9 MODE AV………………………………………………………10 Menu Image……………………………………………………10 OPC………………………………………………………10 Réglages de l’image……………………………………10 Avancé……………………………………………………10 Menu Audio……………………………………………………11 Réglages audio…………………………………………11 Son étendu………………………………………………11 Menu Commande alimentation………………………………12 Aucun sgn arrêt…………………………………………12 Pas d’opé. arrêt………………………... »