Notice PIONEER CP7EX

Notice PIONEER CP7EX

Mode d'emploi PIONEER CP7EX disponible.

Groupe d'entraide des utilisateurs PIONEER CP7EX

Bienvenue dans le groupe d'entraide des utilisateurs
PIONEER CP7EX

Le groupe d'entraide PIONEER CP7EX vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Autoradio. Rejoignez GRATUITEMENT notre groupe d'entraide CP7EX pour vous aider à mieux utiliser votre Autoradio PIONEER. Le SAV entre consommateurs donne accès à différents services pour votre PIONEER CP7EX : accès à la notice CP7EX et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 805 K | Français

Pas de vidéo disponible

« d on a stable, level surface; placing the stand on an unstable surface can be dangerous. Adjust the position as necessary to obtain optimal sound from your system. •Pioneer assumes no liability whatsoever for damages resulting from assembly, improper mounting, insuffi- cient reinforcement, misuse of the product, acts of nature, etc. Assembling the speaker stands Assemble the speaker stands as illustrated below. Please note that a flathead screwdriver will be necessary for assembly. The following illustration shows the fully assem- bled speaker stand: Speaker support Stand base Stand stems Screw slots for securing speaker •Align the screw slots on the stand base and screw holes on the speaker support with the screw holes in the two stems, then insert the screws and tighten. The screw slots allow you to fine-tune the positioning of the speaker. 55 mm Black (SBA6054) 40 mm Black Please note that sunken screw holes are provided in the speaker support. (SBA6051) Screws (Bind head, M6xL40) Nut Spike (SBA6053) Spike base(SLA1057) Screws (Bind head, M6xL55) Speaker support Stand base Stand stems •Make sure you assemble the stand on a flat surface that is relatively soft (such as a carpet). •Make sure the screws are inserted in the screw holes as shown above (with the screw head hidden) when securing the speaker. Improper setup could result in damage or injury if the speaker falls from the stand.3 En English Using the spikes The speaker stand includes spikes that you can use to isolate the speaker from the floor. Spikes are recommended when placing the stand on a thick carpet (for added stability), or for better sound when placing the stand on a hard reverberant surface (such as a concrete or wood floor). Use the supplied spike bases to avoid scratching the floor or other surface where the stand is placed. 1 2 Spike Stand base plate Nut 1Attach the spikes to the nuts provided. 2Attach all four spikes to the threaded metal inserts at the base of the speaker stand. 3Choose the location for speaker placement then put the spike bases on the floor. 4Place the stand so that the spikes are resting on the spike bases on the floor. Before placing the speaker on the speaker stand, make sure the stand is stable and resting squarely on all four spikes. •Note that these spikes are sharp metal and can cause damage to flooring. Make sure to lay down a cloth or suitable base before setting up. •The spike bases should be placed as shown below (with the depression on the top side). •Make sure to use the spike bases provided to avoid damaging the surface where you place the stand. Attaching a speaker to the stand To avoid accident or injury, please use screws to secure the speaker to the speaker stand. Note that there are fastening nuts provided on the speaker base (see below). Secure the speaker to the speaker support using the washer, spring washer and the 60 mm screws as shown below. (SBA6058) Speaker base Speakersupport Washers (SBE6008) Fastening nuts Screws (Bind head, M6xL60) 60 mm Black Spring washer (SBE6007) Screw slotsfor securingspeaker Cabinet and stand maintenance •Use a polishing cloth or dry cloth to wipe off dust and dirt. •If the cabinet or stand is very dirty, use a soft cloth dipped in some neutral cleanser diluted 5 or 6 times with water. Finally, wipe again using a dry cloth. Do not use furniture wax or cleaners. •Never use thinners, benzine,... »

En cours...