Notice WHARFEDALE Diamond 8.3

Notice WHARFEDALE Diamond 8.3

Mode d'emploi WHARFEDALE Diamond 8.3 disponible.

Groupe d'entraide des utilisateurs WHARFEDALE Diamond 8.3

Bienvenue dans le groupe d'entraide des utilisateurs
WHARFEDALE Diamond 8.3

Colonne

Le groupe d'entraide WHARFEDALE Diamond 8.3 vous donne des conseils d'utilisation, solutions aux problèmes de fonctionnement, entretien et assistance pour votre Enceinte acoustique. Rejoignez GRATUITEMENT notre groupe d'entraide Diamond 8.3 pour vous aider à mieux utiliser votre Enceinte acoustique WHARFEDALE. Le SAV entre consommateurs donne accès à différents services pour votre WHARFEDALE Diamond 8.3 : accès à la notice Diamond 8.3 et mode d'emploi pdf, manuel d'utilisation en français, avis consommateur et forum actif. Soyez le premier membre actif de ce groupe d'entraide.

WHARFEDALE Diamond 8.3

Dernières actualités du groupe d'entraide WHARFEDALE Diamond 8.3

Nouvelles questions du forum

Nouveaux membres

  • STEPH5192  depuis le 03/12/2021 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)
  • Youlka89  depuis le 29/12/2020 - Expertise (non renseigné) - Utilisateur depuis (non renseigné)

Documentation disponible sur votre produit

Notice disponible après inscription gratuite au groupe d'entraide

Manuel/Notice/Mode d'emploi | 369 K | Français

Pas de lien disponible

Pas de vidéo disponible

« dvise you. Remember that a loudspeaker can only reproduce the signal with which it is fed. If the recording is bad; the reception of a radio is poor or if the amplifier is distorting, then this will be faithfully reproduced as an unpleasant sound. For this reason you should install the best equipment you can afford and in particular, you should select an amplifier which has good reserves of output power. A high output amplifier will usually sound better than a low powered one and will enhance the reliability of your loudspeakers. This is because a small amplifier will ‘clip’ the music signal when it is asked to deliver a higher output level, beyond that which it is capable of. The resulting clipped signal generates unusually high levels of high frequency distortion which can stress or even damage the tweeter units. For this reason you should always turn down the volume if the music starts to sound distorted. CONNECTING THE LOUDSPEAKERS TO YOUR SYSTEM Always ensure that the amplifier and all associated components are switched OFF before connection commences. NEVER CONNECT THE MAINS ELECTRICITY SUPPLY TO YOUR LOUDSPEAKERS Connect the left hand speaker to your amplifier’s left hand channel, taking care to connect red to red and black to black. Repeat this for the right hand speaker. BINDING POST TERMINALS - EUROPEAN SAFETY REGULATIONS This loudspeaker has been fitted with plastic blocking plugs on the terminals in order to conform with European safety regulations. Customers outside of the European Union who wish to remove these plugs can do so by carefully inserting the tip of a penknife or other pointed tool under the plug and gently prising it out. Separate terminals are provided for feeding the low and high-frequency drive units. You will see that the red terminals are connected together, as are the black; by two metal links. If you wish to use the system conventionally leave the links in place and connect to the amplifier as shown in the diagram. However improved performance can be obtained by either bi-wiring or bi- amping the speakers. To do this, first remove the metal links connecting the pairs of terminals. In the case of bi-wiring connect each of the red terminals on the speaker via separate cables to the red output terminal on the amplifier. Repeat the process for the black terminals. Take care that the left channel outputs are fed to the left hand speakers and similarly for the right hand side. Bi-amping is similar to the above but requires the use of two stereo amplifiers as shown in the diagram. ROOM POSITIONING Your DIAMOND 8loudspeakers offer great flexibility of positioning within your home. Depending upon the model they can be positioned upon shelves, on stands or directly on the floor. All the models can be positioned as close as 0.5m - 1m from a side facing wall. There must be a distance of at least 0.7m - 1m between the backs of the cabinets and the walls. If the loudspeakers are positioned close to the wall they should ideally be angled inwards slightly and be separated by a distance of 3 metres. The performance of the DIAMOND 8loudspeakers may be improved by positioning them further away from the back wall, if you have enough room. In that case you can angle them inwards by 40 degrees, as shown in the diagram. The DIAMOND 8.1, 8.2should ideally be placed on loudspeaker stands or wall brackets well away the floor, with the top of the cabinet at approximately eye level wh... »

En cours...